The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

rndc (8)
  • rndc (1) ( Solaris man: Команды и прикладные программы пользовательского уровня )
  • rndc (8) ( FreeBSD man: Команды системного администрирования )
  • >> rndc (8) ( Linux man: Команды системного администрирования )
  •  

    NAME

    rndc - name server control utility
     
    

    SYNOPSIS

    rndc [ -c config-file ] [ -k key-file ] [ -s server ] [ -p port ] [ -V ] [ -y key_id ] command  

    DESCRIPTION

    rndc controls the operation of a name server. It supersedes the ndc utility that was provided in old BIND releases. If rndc is invoked with no command line options or arguments, it prints a short summary of the supported commands and the available options and their arguments.

    rndc communicates with the name server over a TCP connection, sending commands authenticated with digital signatures. In the current versions of rndc and named, the only supported authentication algorithm is HMAC-MD5, which uses a shared secret on each end of the connection. This provides TSIG-style authentication for the command request and the name server's response. All commands sent over the channel must be signed by a key_id known to the server.

    rndc reads a configuration file to determine how to contact the name server and decide what algorithm and key it should use.  

    OPTIONS

    -c config-file
    Use config-file as the configuration file instead of the default, /etc/rndc.conf.
    -k key-file
    Use key-file as the key file instead of the default, /etc/rndc.key. The key in /etc/rndc.key will be used to authenticate commands sent to the server if the config-file does not exist.
    -s server
    server is the name or address of the server which matches a server statement in the configuration file for rndc. If no server is supplied on the command line, the host named by the default-server clause in the option statement of the configuration file will be used.
    -p port
    Send commands to TCP port port instead of BIND 9's default control channel port, 953.
    -V
    Enable verbose logging.
    -y keyid
    Use the key keyid from the configuration file. keyid must be known by named with the same algorithm and secret string in order for control message validation to succeed. If no keyid is specified, rndc will first look for a key clause in the server statement of the server being used, or if no server statement is present for that host, then the default-key clause of the options statement. Note that the configuration file contains shared secrets which are used to send authenticated control commands to name servers. It should therefore not have general read or write access.

    For the complete set of commands supported by rndc, see the BIND 9 Administrator Reference Manual or run rndc without arguments to see its help message.

    To debug named with rndc, additional package bind-debug have to be installed.

     

    LIMITATIONS

    rndc does not yet support all the commands of the BIND 8 ndc utility.

    There is currently no way to provide the shared secret for a key_id without using the configuration file.

    Several error messages could be clearer.  

    SEE ALSO

    rndc.conf(5), named(8), named.conf(5) ndc(8), BIND 9 Administrator Reference Manual.  

    AUTHOR

    Internet Systems Consortium


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    OPTIONS
    LIMITATIONS
    SEE ALSO
    AUTHOR


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру