The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

re (4)
  • re (3) ( Solaris man: Библиотечные вызовы )
  • re (3) ( Linux man: Библиотечные вызовы )
  • >> re (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    re
    
     - RealTek 8139C+/8169/816xS/811xS/8101E PCI/PCIe Ethernet adapter driver
    
    
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following lines in your kernel configuration file:
    device miibus device re

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    if_re_load="YES"
    
     

    DESCRIPTION

    The driver provides support for various NICs based on the RealTek RTL8139C+, RTL8169, RTL8169S, RTL8110S, RTL8168S, RTL8111S and RTL8101E PCI and PCIe Ethernet controllers.

    NICs based on the 8139C+ and 8101E are capable of 10 and 100Mbps speeds over CAT5 cable. NICs based on the 8169, 816xS and 811xS are capable of 10, 100 and 1000Mbps operation.

    All NICs supported by the driver have TCP/IP checksum offload and hardware VLAN tagging/insertion features, and use a descriptor-based DMA mechanism. They are also capable of TCP large send (TCP segmentation offload).

    The 8139C+ is a single-chip solution combining both a 10/100 MAC and PHY. The 8169 is a 10/100/1000 MAC only, requiring a GMII or TBI external PHY. The 8169S and 8110S are single-chip devices containing both a 10/100/1000 MAC and 10/100/1000 copper PHY. Standalone 10/100/1000 cards are available in both 32-bit PCI and 64-bit PCI models. The 8110S is designed for embedded LAN-on-motherboard applications.

    The 8169, 8169S and 8110S also support jumbo frames, which can be configured via the interface MTU setting. The MTU is limited to 7422, since the chip cannot transmit larger frames. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit jumbo frames.

    The driver supports the following media types:

    autoselect
    Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf5.
    10baseT/UTP
    Set 10Mbps operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.
    100baseTX
    Set 100Mbps (Fast Ethernet) operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.
    1000baseTX
    Set 1000baseTX operation over twisted pair. The RealTek gigE chips support 1000Mbps in full-duplex mode only.

    The driver supports the following media options:

    full-duplex
    Force full duplex operation.
    half-duplex
    Force half duplex operation.

    For more information on configuring this device, see ifconfig(8).  

    HARDWARE

    The driver supports RealTek RTL8139C+, RTL8169, RTL816xS, RTL811xS, and RTL8101E based Fast Ethernet and Gigabit Ethernet adapters including:

     

    DIAGNOSTICS

    "re%d: couldn't map memory"
    A fatal initialization error has occurred.
    "re%d: couldn't map ports"
    A fatal initialization error has occurred.
    "re%d: couldn't map interrupt"
    A fatal initialization error has occurred.
    "re%d: no memory for softc struct!"
    The driver failed to allocate memory for per-device instance information during initialization.
    "re%d: failed to enable memory mapping!"
    The driver failed to initialize PCI shared memory mapping. This might happen if the card is not in a bus-master slot.
    "re%d: no memory for jumbo buffers!"
    The driver failed to allocate memory for jumbo frames during initialization.
    "re%d: watchdog timeout"
    The device has stopped responding to the network, or there is a problem with the network connection (cable).

     

    SEE ALSO

    altq(4), arp(4), miibus(4), netintro(4), ng_ether4, polling(4), vlan(4), ifconfig(8)
    RealTek Semiconductor RTL8139C+, RTL8169, RTL8169S and RTL8110S datasheets http://www.realtek.com.tw/
     

    HISTORY

    The device driver first appeared in Fx 5.2 .  

    AUTHORS

    The driver was written by An Bill Paul Aq wpaul@windriver.com .  

    BUGS

    The Xterasys XN-152 32-bit PCI NIC, which uses the RTL8169 MAC and Marvell 88E1000 PHY, has a defect that causes DMA corruption if the board is plugged into a 64-bit PCI slot. The defect lies in the board design, not the chip itself: the PCI REQ64# and ACK64# lines should be pulled high, but they are not. The result is that the 8169 chip is tricked into performing 64-bit DMA transfers even though a 64-bit data path between the NIC and the bus does not actually exist.

    Unfortunately, it is not possible to correct this problem in software, however it is possible to detect it. When the driver is loaded, it will run a diagnostic routine designed to validate DMA operation by placing the chip in digital loopback mode and initiating a packet transmission. If the card functions properly, the transmitted data will be echoed back unmodified. If the echoed data is corrupt, the driver will print an error message on the console and abort the device attach. The user should insure the NIC is installed in a 32-bit PCI slot to avoid this problem.

    The RealTek 8169, 8169S and 8110S chips appear to only be capable of transmitting jumbo frames up to 7.5K in size.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    DIAGNOSTICS
    SEE ALSO
    HISTORY
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру