The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ng_atm (4)
  • >> ng_atm (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ng_atm
    
     - netgraph ATM node type
    
     
    

    SYNOPSIS

       #include <sys/types.h>
       #include <net/if_atm.h>
       #include <netgraph.h>
       #include <netgraph/atm/ng_atm.h>
     

    DESCRIPTION

    The atm netgraph node type allows natm(4) ATM drivers to be connected to the netgraph(4) networking subsystem. When the module is loaded a node is automatically created for each natm(4) ATM interface. The nodes are named with the same name as the interface. Nodes are also created if a driver for an ATM card is loaded after was loaded.

    The atm nodes are persistent. They are removed when the interface is removed. NGM_SHUTDOWN messages are ignored by the node.  

    HOOKS

    Four special hooks with fixed names and an unlimited number of hooks with user defined names are supported. Three of the fixed hooks are attached to strategic points in the information flow in the natm(4) system and support only reading. The fourth fixed hook behaves like the other user hooks, but a number of management messages are sent along the hook. The other hooks can be attached to VCIs dynamically by means of control messages to the atm node and can be written and read.

    The four fixed hooks are:

    input
    This is a connection to the raw input stream from the network. If this hook is connected, all incoming packets are delivered out to this hook. Note that this redirects ALL input. Neither natm(4) nor the user hooks will see any input if input is connected. An Vt atm_pseudohdr (see natm(4)) is prepended to the actual data.
    output
    This is a connection to the raw output stream to the network device. If this hook is connected, all outgoing packets are handed over to the netgraph system and delivered to the hook instead of being delivered to the ATM driver. An Vt atm_pseudohdr (see natm(4)) is prepended to the actual data.
    orphans
    This hook receives all packets that are unrecognized, i.e., do not belong to either a natm(4) socket, a VCI or natm(4) IP. Because ATM is connection oriented and packets are received on a given VCI only when someone initiates this VCI, packets should never be orphaned. There is however one exception: if you use natm(4) IP with LLC/SNAP encapsulation packets with do not have the IP protocol indicated in the packet header are delivered out of this hook. An Vt atm_pseudohdr (see natm(4)) is prepended to the actual data send out to the hook.
    manage
    This hook behaves exactly like a normal user hook (see below) except that the node at the other hand will receive management messages.

    Hooks for dynamically initiated VCIs can have whatever name is allowed by netgraph(4) as long as the name does not collide with one of the three predefined names.

    To initiate packet sending an receiving on a dynamic hook one has to issue a NGM_ATM_CPCS_INIT control message. To terminate sending and receiving one must send a NGM_ATM_CPCS_TERM message (see Sx CONTROL MESSAGES ) . The data sent and received on these hooks has no additional headers.  

    CONTROL MESSAGES

    This node type supports the generic messages plus the following:

    NGM_ATM_GET_IFNAME
    Return the name of the interface as a NUL -terminated string. This is normally the same name as that of the node.
    NGM_ATM_GET_CONFIG
    Returns a structure defining the configuration of the interface:
    struct ng_atm_config {
            uint32_t        pcr;            /* peak cell rate */
            uint32_t        maxvpi;         /* maximum vpi */
            uint32_t        maxvci;         /* maximum vci */
            uint32_t        max_vpcs;       /* maximum number of VPCs */
            uint32_t        max_vccs;       /* maximum number of VCCs */
    };
    
    NGM_ATM_GET_VCCS
    Returns the table of open VCCs from the driver. This table consists of a header and a variable sized array of entries, one for each open VCC:
    struct atmio_vcctable {
            uint32_t        count;          /* number of vccs */
            struct atmio_vcc vccs[0];       /* array of VCCs */
    };
    struct atmio_vcc {
            uint16_t        flags;          /* flags */
            uint16_t        vpi;            /* VPI */
            uint16_t        vci;            /* VCI */
            uint16_t        rmtu;           /* Receive maximum CPCS size */
            uint16_t        tmtu;           /* Transmit maximum CPCS size */
            uint8_t         aal;            /* aal type */
            uint8_t         traffic;        /* traffic type */
            struct atmio_tparam tparam;     /* traffic parameters */
    };
    struct atmio_tparam {
            uint32_t        pcr;    /* 24bit: Peak Cell Rate */
            uint32_t        scr;    /* 24bit: VBR Sustainable Cell Rate */
            uint32_t        mbs;    /* 24bit: VBR Maximum burst size */
            uint32_t        mcr;    /* 24bit: MCR */
            uint32_t        icr;    /* 24bit: ABR ICR */
            uint32_t        tbe;    /* 24bit: ABR TBE (1...2^24-1) */
            uint8_t         nrm;    /*  3bit: ABR Nrm */
            uint8_t         trm;    /*  3bit: ABR Trm */
            uint16_t        adtf;   /* 10bit: ABR ADTF */
            uint8_t         rif;    /*  4bit: ABR RIF */
            uint8_t         rdf;    /*  4bit: ABR RDF */
            uint8_t         cdf;    /*  3bit: ABR CDF */
    };
    

    Note that this is the driver's table, so all VCCs opened via natm(4) sockets and IP are also shown. They can, however, be distinguished by their flags. The flags field contains the following flags:

    ATM_PH_AAL5
    use AAL5 instead of AAL0
    ATM_PH_LLCSNAP
    if AAL5 use LLC SNAP encapsulation
    ATM_FLAG_NG
    this is a netgraph VCC
    ATM_FLAG_HARP
    this is a HARP VCC
    ATM_FLAG_NORX
    transmit only VCC
    ATM_FLAG_NOTX
    receive only VCC
    ATMIO_FLAG_PVC
    treat channel as a PVC

    If the ATM_FLAG_NG flag is set, then traffic and tparam contain meaningful information.

    The aal field contains one of the following values:

    ATMIO_AAL_0
    AAL 0 (raw cells)
    ATMIO_AAL_34
    AAL 3 or AAL 4
    ATMIO_AAL_5
    AAL 5
    ATMIO_AAL_RAW
    device specific raw cells

    The traffic field can have one of the following values (not all drivers support all traffic types however):

    ATMIO_TRAFFIC_UBR
    ATMIO_TRAFFIC_CBR
    ATMIO_TRAFFIC_ABR
    ATMIO_TRAFFIC_VBR

    NGM_ATM_CPCS_INIT
    Initialize a VCC for sending and receiving. The argument is a structure:
    struct ng_atm_cpcs_init {
            char            name[NG_HOOKSIZ];
            uint32_t        flags;          /* flags. (if_natmio.h) */
            uint16_t        vci;            /* VCI to open */
            uint16_t        vpi;            /* VPI to open */
            uint16_t        rmtu;           /* receive maximum PDU */
            uint16_t        tmtu;           /* transmit maximum PDU */
            uint8_t         aal;            /* AAL type (if_natmio.h) */
            uint8_t         traffic;        /* traffic type (if_natmio.h) */
            uint32_t        pcr;            /* Peak cell rate */
            uint32_t        scr;            /* Sustainable cell rate */
            uint32_t        mbs;            /* Maximum burst size */
            uint32_t        mcr;            /* Minimum cell rate */
            uint32_t        icr;            /* ABR: Initial cell rate */
            uint32_t        tbe;            /* ABR: Transmit buffer exposure */
            uint8_t         nrm;            /* ABR: Nrm */
            uint8_t         trm;            /* ABR: Trm */
            uint16_t        adtf;           /* ABR: ADTF */
            uint8_t         rif;            /* ABR: RIF */
            uint8_t         rdf;            /* ABR: RDF */
            uint8_t         cdf;            /* ABR: CDF */
    };
    

    The name field is the name of the hook for which sending and receiving should be enabled. This hook must already be connected. The vpi and vci fields are the respective VPI and VCI values to use for the ATM cells. They must be within the range, given by the maxvpi and maxvci fields of the Vt ng_atm_config structure. The flags field contains the flags (see above) and the other fields describe the type of traffic.

    NGM_ATM_CPCS_TERM
    Stop sending and receiving on the indicated hook. The argument is a
    struct ng_atm_cpcs_term {
            char            name[NG_HOOKSIZ];
    };
    

     

    MANAGEMENT MESSAGES

    If the manage hook is connected, certain messages are sent along the hook. They are received by the peer node with a cookie of NG_ATM_COOKIE

    NGM_ATM_CARRIER_CHANGE
    The carrier state of the ATM physical interface has changed. The message has the following structure:
    struct ng_atm_carrier_change {
            uint32_t        node;
            uint32_t        state;
    };
    

    The node field is the node ID of the ATM node. This can be used by the managing entity (for example ilmid(8)) to manage several interfaces at the same time through the same node. The state field is 1 if the carrier was detected, and 0 if it was lost.

    NGM_ATM_VCC_CHANGE
    A permanent VCC has been added, deleted or changed. This is used by ilmid(8) to generate the appropriate ILMI traps. The structure of the message is:
    struct ng_atm_vcc_change {
            uint32_t        node;
            uint16_t        vci;
            uint8_t         vpi;
            uint8_t         state;
    };
    
    Where state is 0 if the PVC was deleted, and 1 if it was added or modified.

     

    FLOW CONTROL

    If the hardware driver supports it, the node can emit flow control messages along a user hook. The format of these messages is described in In netgraph/ng_message.h . The atm node may generate NGM_HIGH_WATER_PASSED and NGM_LOW_WATER_PASSED messages. The first one indicates that the hardware driver has stopped output on the channel and drops new packets, the second one reports that output was reenabled. Currently, the structures are not filled with information.  

    SHUTDOWN

    The nodes are persistent as long as the corresponding interface exists. Upon receipt of a NGM_SHUTDOWN messages, all hooks are disconnected and the node is reinitialized. All VCCs opened via netgraph(4) are closed. When the ATM interface is unloaded, the node disappears. If the node is compiled with NGATM_DEBUG there is a sysctl net.graph.atm.allow_shutdown which, when set to a non-zero value, allows the nodes to shut down. Note that this is intended for development only and may lead to kernel panics if set.  

    SEE ALSO

    natm(4), netgraph(4), ng_ether4, ngctl(8)  

    AUTHORS

    An Harti Brandt Aq harti@FreeBSD.org


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HOOKS
    CONTROL MESSAGES
    MANAGEMENT MESSAGES
    FLOW CONTROL
    SHUTDOWN
    SEE ALSO
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру