>>ну ежли не поможет, могу выкатить свой конфиг, у меня данная опция работает
>>
>Было бы интересно посмотреть.
######################################################################
# MAIN CONFIGURATION SETTINGS #
######################################################################
hide pgsql_servers = (/tmp/.s.PGSQL.5432)/mail/mailuser/crossword
######################################################################
# Specify your host's canonical name here. This should normally be the fully
# qualified "official" name of your host. If this option is not set, the
# uname() function is called to obtain the name. In many cases this does
# the right thing and you need not set anything explicitly.
primary_hostname = local.net
# The next three settings create two lists of domains and one list of hosts.
# These lists are referred to later in this configuration using the syntax
# +local_domains, +relay_to_domains, and +relay_from_hosts, respectively. They
# are all colon-separated lists:
domainlist local_domains = local.net
domainlist relay_to_domains =
hostlist relay_from_hosts = localhost
# Most straightforward access control requirements can be obtained by
# appropriate settings of the above options. In more complicated situations,
# you may need to modify the Access Control List (ACL) which appears later in
# this file.
# The first setting specifies your local domains, for example:
#
# domainlist local_domains = my.first.domain : my.second.domain
#
# You can use "@" to mean "the name of the local host", as in the default
# setting above. This is the name that is specified by primary_hostname,
# as specified above (or defaulted). If you do not want to do any local
# deliveries, remove the "@" from the setting above. If you want to accept mail
# addressed to your host's literal IP address, for example, mail addressed to
# "user@[192.168.23.44]", you can add "@[]" as an item in the local domains
# list. You also need to uncomment "allow_domain_literals" below. This is not
# recommended for today's Internet.
# The second setting specifies domains for which your host is an incoming relay.
# If you are not doing any relaying, you should leave the list empty. However,
# if your host is an MX backup or gateway of some kind for some domains, you
# must set relay_to_domains to match those domains. For example:
#
# domainlist relay_to_domains = *.myco.com : my.friend.org
#
# This will allow any host to relay through your host to those domains.
# See the section of the manual entitled "Control of relaying" for more
# information.
# The third setting specifies hosts that can use your host as an outgoing relay
# to any other host on the Internet. Such a setting commonly refers to a
# complete local network as well as the localhost. For example:
#
# hostlist relay_from_hosts = 127.0.0.1 : 192.168.0.0/16
#
# The "/16" is a bit mask (CIDR notation), not a number of hosts. Note that you
# have to include 127.0.0.1 if you want to allow processes on your host to send
# SMTP mail by using the loopback address. A number of MUAs use this method of
# sending mail.
# All three of these lists may contain many different kinds of item, including
# wildcarded names, regular expressions, and file lookups. See the reference
# manual for details. The lists above are used in the access control lists for
# checking incoming messages. The names of these ACLs are defined here:
acl_smtp_rcpt = acl_check_rcpt
# acl_smtp_mime = acl_check_mime
acl_smtp_data = acl_check_data
# You should not change those settings until you understand how ACLs work.
# If you are running a version of Exim that was compiled with the content-
# scanning extension, you can cause incoming messages to be automatically
# scanned for viruses. You have to modify the configuration in two places to
# set this up. The first of them is here, where you define the interface to
# your scanner. This example is typical for ClamAV; see the manual for details
# of what to set for other virus scanners. The second modification is in the
# acl_check_data access control list (see below).
av_scanner = clamd:/var/run/clamav/clamd
# For spam scanning, there is a similar option that defines the interface to
# SpamAssassin. You do not need to set this if you are using the default, which
# is shown in this commented example. As for virus scanning, you must also
# modify the acl_check_data access control list to enable spam scanning.
spamd_address = 127.0.0.1 783
# Specify the domain you want to be added to all unqualified addresses
# here. An unqualified address is one that does not contain an "@" character
# followed by a domain. For example, "caesar@rome.example" is a fully qualified
# address, but the string "caesar" (i.e. just a login name) is an unqualified
# email address. Unqualified addresses are accepted only from local callers by
# default. See the recipient_unqualified_hosts option if you want to permit
# unqualified addresses from remote sources. If this option is not set, the
# primary_hostname value is used for qualification.
qualify_domain = local.net
# If you want unqualified recipient addresses to be qualified with a different
# domain to unqualified sender addresses, specify the recipient domain here.
# If this option is not set, the qualify_domain value is used.
# qualify_recipient =
# The following line must be uncommented if you want Exim to recognize
# addresses of the form "user@[10.11.12.13]" that is, with a "domain literal"
# (an IP address) instead of a named domain. The RFCs still require this form,
# but it makes little sense to permit mail to be sent to specific hosts by
# their IP address in the modern Internet. This ancient format has been used
# by those seeking to abuse hosts by using them for unwanted relaying. If you
# really do want to support domain literals, uncomment the following line, and
# see also the "domain_literal" router below.
# allow_domain_literals
# No deliveries will ever be run under the uids of these users (a colon-
# separated list). An attempt to do so causes a panic error to be logged, and
# the delivery to be deferred. This is a paranoic safety catch. There is an
# even stronger safety catch in the form of the FIXED_NEVER_USERS setting
# in the configuration for building Exim. The list of users that it specifies
# is built into the binary, and cannot be changed. The option below just adds
# additional users to the list. The default for FIXED_NEVER_USERS is "root",
# but just to be absolutely sure, the default here is also "root".
# Note that the default setting means you cannot deliver mail addressed to root
# as if it were a normal user. This isn't usually a problem, as most sites have
# an alias for root that redirects such mail to a human administrator.
exim_user = mailnull
exim_group = mail
never_users = root
###
spool_directory = /var/spool/exim
# The setting below causes Exim to do a reverse DNS lookup on all incoming
# IP calls, in order to get the true host name. If you feel this is too
# expensive, you can specify the networks for which a lookup is done, or
# remove the setting entirely.
host_lookup = *
# The settings below, which are actually the same as the defaults in the
# code, cause Exim to make RFC 1413 (ident) callbacks for all incoming SMTP
# calls. You can limit the hosts to which these calls are made, and/or change
# the timeout that is used. If you set the timeout to zero, all RFC 1413 calls
# are disabled. RFC 1413 calls are cheap and can provide useful information
# for tracing problem messages, but some hosts and firewalls have problems
# with them. This can result in a timeout instead of an immediate refused
# connection, leading to delays on starting up an SMTP session.
rfc1413_hosts = *
rfc1413_query_timeout = 30s
# By default, Exim expects all envelope addresses to be fully qualified, that
# is, they must contain both a local part and a domain. If you want to accept
# unqualified addresses (just a local part) from certain hosts, you can specify
# these hosts by setting one or both of
#
# sender_unqualified_hosts =
# recipient_unqualified_hosts =
#
# to control sender and recipient addresses, respectively. When this is done,
# unqualified addresses are qualified using the settings of qualify_domain
# and/or qualify_recipient (see above).
# If you want Exim to support the "percent hack" for certain domains,
# uncomment the following line and provide a list of domains. The "percent
# hack" is the feature by which mail addressed to x%y@z (where z is one of
# the domains listed) is locally rerouted to x@y and sent on. If z is not one
# of the "percent hack" domains, x%y is treated as an ordinary local part. This
# hack is rarely needed nowadays; you should not enable it unless you are sure
# that you really need it.
#
# percent_hack_domains =
#
# As well as setting this option you will also need to remove the test
# for local parts containing % in the ACL definition below.
# When Exim can neither deliver a message nor return it to sender, it "freezes"
# the delivery error message (aka "bounce message"). There are also other
# circumstances in which messages get frozen. They will stay on the queue for
# ever unless one of the following options is set.
# This option unfreezes frozen bounce messages after two days, tries
# once more to deliver them, and ignores any delivery failures.
ignore_bounce_errors_after = 2d
# This option cancels (removes) frozen messages that are older than a week.
timeout_frozen_after = 7d
######################################################################
daemon_smtp_ports = 25 : 465
smtp_accept_max = 50
smtp_accept_max_per_host = 25
smtp_accept_max_per_connection = 50
smtp_connect_backlog = 50
check_spool_space = 64M
message_size_limit = 8M
log_selector = \
+all_parents \
+lost_incoming_connection \
+received_sender \
+received_recipients \
+smtp_confirmation \
+smtp_syntax_error \
+smtp_protocol_error \
-queue_run
auth_advertise_hosts = ${if eq{$tls_cipher}{}{}{*}}
tls_advertise_hosts = *
tls_verify_certificates = *
tls_certificate = /usr/local/certs/smtp.crt
tls_privatekey = /usr/local/certs/smtp.key
tls_on_connect_ports = 465
######################################################################
# ACL CONFIGURATION #
# Specifies access control lists for incoming SMTP mail #
######################################################################
begin acl
# This access control list is used for every RCPT command in an incoming
# SMTP message. The tests are run in order until the address is either
# accepted or denied.
acl_check_rcpt:
# Accept if the source is local SMTP (i.e. not over TCP/IP). We do this by
# testing for an empty sending host field.
accept hosts = :
#############################################################################
# The following section of the ACL is concerned with local parts that contain
# @ or % or ! or / or | or dots in unusual places.
#
# The characters other than dots are rarely found in genuine local parts, but
# are often tried by people looking to circumvent relaying restrictions.
# Therefore, although they are valid in local parts, these rules lock them
# out, as a precaution.
#
# Empty components (two dots in a row) are not valid in RFC 2822, but Exim
# allows them because they have been encountered. (Consider local parts
# constructed as "firstinitial.secondinitial.familyname" when applied to
# someone like me, who has no second initial.) However, a local part starting
# with a dot or containing /../ can cause trouble if it is used as part of a
# file name (e.g. for a mailing list). This is also true for local parts that
# contain slashes. A pipe symbol can also be troublesome if the local part is
# incorporated unthinkingly into a shell command line.
#
# Two different rules are used. The first one is stricter, and is applied to
# messages that are addressed to one of the local domains handled by this
# host. The line "domains = +local_domains" restricts it to domains that are
# defined by the "domainlist local_domains" setting above. The rule blocks
# local parts that begin with a dot or contain @ % ! / or |. If you have
# local accounts that include these characters, you will have to modify this
# rule.
deny message = Restricted characters in address
domains = +local_domains
local_parts = ^[.] : ^.*[@%!/|]
# The second rule applies to all other domains, and is less strict. The line
# "domains = !+local_domains" restricts it to domains that are NOT defined by
# the "domainlist local_domains" setting above. The exclamation mark is a
# negating operator. This rule allows your own users to send outgoing
# messages to sites that use slashes and vertical bars in their local parts.
# It blocks local parts that begin with a dot, slash, or vertical bar, but
# allows these characters within the local part. However, the sequence /../
# is barred. The use of @ % and ! is blocked, as before. The motivation here
# is to prevent your users (or your users' viruses) from mounting certain
# kinds of attack on remote sites.
deny message = Restricted characters in address
domains = !+local_domains
local_parts = ^[./|] : ^.*[@%!] : ^.*/\\.\\./
#############################################################################
# Accept mail to postmaster in any local domain, regardless of the source,
# and without verifying the sender.
accept local_parts = postmaster
domains = +local_domains
# Deny unless the sender address can be verified.
require verify = sender
# Accept if the message comes from one of the hosts for which we are an
# outgoing relay. It is assumed that such hosts are most likely to be MUAs,
# so we set control=submission to make Exim treat the message as a
# submission. It will fix up various errors in the message, for example, the
# lack of a Date: header line. If you are actually relaying out out from
# MTAs, you may want to disable this. If you are handling both relaying from
# MTAs and submissions from MUAs you should probably split them into two
# lists, and handle them differently.
# Recipient verification is omitted here, because in many cases the clients
# are dumb MUAs that don't cope well with SMTP error responses. If you are
# actually relaying out from MTAs, you should probably add recipient
# verification here.
# Note that, by putting this test before any DNS black list checks, you will
# always accept from these hosts, even if they end up on a black list. The
# assumption is that they are your friends, and if they get onto a black
# list, it is a mistake.
accept hosts = +relay_from_hosts
control = submission
# Accept if the message arrived over an authenticated connection, from
# any host. Again, these messages are usually from MUAs, so recipient
# verification is omitted, and submission mode is set. And again, we do this
# check before any black list tests.
accept authenticated = *
control = submission
#############################################################################
# There are no default checks on DNS black lists because the domains that
# contain these lists are changing all the time. However, here are two
# examples of how you can get Exim to perform a DNS black list lookup at this
# point. The first one denies, whereas the second just warns.
#
# deny message = rejected because $sender_host_address is in a black list at $dnslist_domain\n$dnslist_text
# dnslists = black.list.example
#
# warn message = X-Warning: $sender_host_address is in a black list at $dnslist_domain
# log_message = found in $dnslist_domain
# dnslists = black.list.example
#############################################################################
#############################################################################
# This check is commented out because it is recognized that not every
# sysadmin will want to do it. If you enable it, the check performs
# Client SMTP Authorization (csa) checks on the sending host. These checks
# do DNS lookups for SRV records. The CSA proposal is currently (May 2005)
# an Internet draft. You can, of course, add additional conditions to this
# ACL statement to restrict the CSA checks to certain hosts only.
#
# require verify = csa
#############################################################################
# Accept if the address is in a local domain, but only if the recipient can
# be verified. Otherwise deny. The "endpass" line is the border between
# passing on to the next ACL statement (if tests above it fail) or denying
# access (if tests below it fail).
accept domains = +local_domains
endpass
verify = recipient
# Accept if the address is in a domain for which we are an incoming relay,
# but again, only if the recipient can be verified.
accept domains = +relay_to_domains
endpass
verify = recipient
# Reaching the end of the ACL causes a "deny", but we might as well give
# an explicit message.
deny message = relay not permitted
# This ACL is used after the contents of a message have been received. This
# is the ACL in which you can test a message's headers or body, and in
# particular, this is where you can invoke external virus or spam scanners.
# Some suggested ways of configuring these tests are shown below, commented
# out. Without any tests, this ACL accepts all messages. If you want to use
# such tests, you must ensure that Exim is compiled with the content-scanning
# extension (WITH_CONTENT_SCAN=yes in Local/Makefile).
acl_check_data:
# Deny if the message contains a virus. Before enabling this check, you
# must install a virus scanner and set the av_scanner option above.
deny malware = *
message = This message contains a virus ($malware_name).
# Add headers to a message if it is judged to be spam. Before enabling this,
# you must install SpamAssassin. You may also need to set the spamd_address
# option above.
#
# warn spam = nobody
# message = X-Spam_score: $spam_score\n\
# X-Spam_score_int: $spam_score_int\n\
# X-Spam_bar: $spam_bar\n\
# X-Spam_report: $spam_report
warn message = X-Spam-Score: $spam_score ($spam_bar)
hosts = !+relay_from_hosts
spam = nobody:true
warn message = X-Spam-Report: $spam_report
hosts = !+relay_from_hosts
spam = nobody:true
warn message = Subject: ***SPAM*** $h_Subject:
hosts = !+relay_from_hosts
spam = nobody
deny message = This message scored $spam_score spam points.
spam = nobody:true
hosts = !+relay_from_hosts
condition = ${if >{$spam_score_int}{120}{1}{0}}
# Accept the message.
accept
#####################
#acl_check_auth:
#
# accept encrypted = *
#
# deny message = TLS encryption or CRAM-MD5 required
######################################################################
# ROUTERS CONFIGURATION #
# Specifies how addresses are handled #
######################################################################
# THE ORDER IN WHICH THE ROUTERS ARE DEFINED IS IMPORTANT! #
# An address is passed to each router in turn until it is accepted. #
######################################################################
begin routers
#####################
smart_route:
driver = manualroute
domains = ! +local_domains
transport = remote_smtp
route_list = * smart.local.net
# This router routes to remote hosts over SMTP by explicit IP address,
# when an email address is given in "domain literal" form, for example,
# <user@[192.168.35.64]>. The RFCs require this facility. However, it is
# little-known these days, and has been exploited by evil people seeking
# to abuse SMTP relays. Consequently it is commented out in the default
# configuration. If you uncomment this router, you also need to uncomment
# allow_domain_literals above, so that Exim can recognize the syntax of
# domain literal addresses.
# domain_literal:
# driver = ipliteral
# domains = ! +local_domains
# transport = remote_smtp
# This router routes addresses that are not in local domains by doing a DNS
# lookup on the domain name. The exclamation mark that appears in "domains = !
# +local_domains" is a negating operator, that is, it can be read as "not". The
# recipient's domain must not be one of those defined by "domainlist
# local_domains" above for this router to be used.
#
# If the router is used, any domain that resolves to 0.0.0.0 or to a loopback
# interface address (127.0.0.0/8) is treated as if it had no DNS entry. Note
# that 0.0.0.0 is the same as 0.0.0.0/32, which is commonly treated as the
# local host inside the network stack. It is not 0.0.0.0/0, the default route.
# If the DNS lookup fails, no further routers are tried because of the no_more
# setting, and consequently the address is unrouteable.
# dnslookup:
# driver = dnslookup
# domains = ! +local_domains
# transport = remote_smtp
# ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
# no_more
# The remaining routers handle addresses in the local domain(s), that is those
# domains that are defined by "domainlist local_domains" above.
# This router handles aliasing using a linearly searched alias file with the
# name /etc/aliases. When this configuration is installed automatically,
# the name gets inserted into this file from whatever is set in Exim's
# build-time configuration. The default path is the traditional /etc/aliases.
# If you install this configuration by hand, you need to specify the correct
# path in the "data" setting below.
#
##### NB You must ensure that the alias file exists. It used to be the case
##### NB that every Unix had that file, because it was the Sendmail default.
##### NB These days, there are systems that don't have it. Your aliases
##### NB file should at least contain an alias for "postmaster".
#
# If any of your aliases expand to pipes or files, you will need to set
# up a user and a group for these deliveries to run under. You can do
# this by uncommenting the "user" option below (changing the user name
# as appropriate) and adding a "group" option if necessary. Alternatively, you
# can specify "user" on the transports that are used. Note that the transports
# listed below are the same as are used for .forward files; you might want
# to set up different ones for pipe and file deliveries from aliases.
# system_aliases:
# driver = redirect
# allow_fail
# allow_defer
# data = ${lookup{$local_part}lsearch{/etc/aliases}}
# user = mailnull
# group = mail
# file_transport = address_file
# pipe_transport = address_pipe
system_aliases:
driver = redirect
allow_fail
allow_defer
data = ${lookup pgsql{SELECT alias FROM aliases \
WHERE mail='$local_part@$domain'}{$value}fail}
user = mailnull
group = mail
file_transport = address_file
pipe_transport = address_pipe
# This router handles forwarding using traditional .forward files in users'
# home directories. If you want it also to allow mail filtering when a forward
# file starts with the string "# Exim filter" or "# Sieve filter", uncomment
# the "allow_filter" option.
# If you want this router to treat local parts with suffixes introduced by "-"
# or "+" characters as if the suffixes did not exist, uncomment the two local_
# part_suffix options. Then, for example, xxxx-foo@your.domain will be treated
# in the same way as xxxx@your.domain by this router. You probably want to make
# the same change to the localuser router.
# The no_verify setting means that this router is skipped when Exim is
# verifying addresses. Similarly, no_expn means that this router is skipped if
# Exim is processing an EXPN command.
# The check_ancestor option means that if the forward file generates an
# address that is an ancestor of the current one, the current one gets
# passed on instead. This covers the case where A is aliased to B and B
# has a .forward file pointing to A.
# The three transports specified at the end are those that are used when
# forwarding generates a direct delivery to a file, or to a pipe, or sets
# up an auto-reply, respectively.
# userforward:
# driver = redirect
# check_local_user
# # local_part_suffix = +* : -*
# # local_part_suffix_optional
# file = $home/.forward
# # allow_filter
# no_verify
# no_expn
# check_ancestor
# file_transport = address_file
# pipe_transport = address_pipe
# reply_transport = address_reply
# condition = ${if exists{$home/.forward} {yes} {no} }
# This router matches local user mailboxes. If the router fails, the error
# message is "Unknown user".
# If you want this router to treat local parts with suffixes introduced by "-"
# or "+" characters as if the suffixes did not exist, uncomment the two local_
# part_suffix options. Then, for example, xxxx-foo@your.domain will be treated
# in the same way as xxxx@your.domain by this router.
# localuser:
# driver = accept
# check_local_user
# # local_part_suffix = +* : -*
# # local_part_suffix_optional
# transport = local_delivery
# cannot_route_message = Unknown user
localuser:
driver = accept
condition = ${lookup pgsql{SELECT uid FROM users \
WHERE login = '$local_part@$domain'}{yes}{no}}
transport = local_delivery
cannot_route_message = Unknown user
######################################################################
# TRANSPORTS CONFIGURATION #
######################################################################
# ORDER DOES NOT MATTER #
# Only one appropriate transport is called for each delivery. #
######################################################################
# A transport is used only when referenced from a router that successfully
# handles an address.
begin transports
# This transport is used for delivering messages over SMTP connections.
remote_smtp:
driver = smtp
# This transport is used for local delivery to user mailboxes in traditional
# BSD mailbox format. By default it will be run under the uid and gid of the
# local user, and requires the sticky bit to be set on the /var/mail directory.
# Some systems use the alternative approach of running mail deliveries under a
# particular group instead of using the sticky bit. The commented options below
# show how this can be done.
# local_delivery:
# driver = appendfile
# file = /var/mail/$local_part
# delivery_date_add
# envelope_to_add
# return_path_add
# group = mail
# user = $local_part
# mode = 0660
# no_mode_fail_narrower
local_delivery:
driver = appendfile
directory = ${lookup pgsql{SELECT maildir FROM users \
WHERE login = '$local_part@$domain'}{$value}fail}
create_directory
directory_mode = 0770
maildir_format
delivery_date_add
envelope_to_add
return_path_add
group = ${lookup pgsql{SELECT gid FROM users \
WHERE login = '$local_part@$domain'}{$value}fail}
user = ${lookup pgsql{SELECT uid FROM users \
WHERE login = '$local_part@$domain'}{$value}fail}
mode = 0660
no_mode_fail_narrower
quota = ${lookup pgsql{SELECT quota FROM users \
WHERE login = '$local_part@$domain'}{$value}fail}M
quota_warn_message = " \
From: Mail Delivery System <Mailer-Daemon@local.net>\n \
Reply-to: support@local.net\n \
To: $local_part@$domain\n \
Subject: Mail quota warning\n \
This message is automaticaly generated by your mail server\n \
This means, that your maildir is 75% full. If you would\n \
override this limit new mail would not be delivered to you!\n"
quota_warn_threshold = 75%
# This transport is used for handling pipe deliveries generated by alias or
# .forward files. If the pipe generates any standard output, it is returned
# to the sender of the message as a delivery error. Set return_fail_output
# instead of return_output if you want this to happen only when the pipe fails
# to complete normally. You can set different transports for aliases and
# forwards if you want to - see the references to address_pipe in the routers
# section above.
address_pipe:
driver = pipe
return_output
# This transport is used for handling deliveries directly to files that are
# generated by aliasing or forwarding.
address_file:
driver = appendfile
delivery_date_add
envelope_to_add
return_path_add
# This transport is used for handling autoreplies generated by the filtering
# option of the userforward router.
address_reply:
driver = autoreply
######################################################################
# RETRY CONFIGURATION #
######################################################################
begin retry
# This single retry rule applies to all domains and all errors. It specifies
# retries every 15 minutes for 2 hours, then increasing retry intervals,
# starting at 1 hour and increasing each time by a factor of 1.5, up to 16
# hours, then retries every 6 hours until 4 days have passed since the first
# failed delivery.
# Address or Domain Error Retries
# ----------------- ----- -------
* * F,2h,15m; G,16h,1h,1.5; F,4d,6h
######################################################################
# REWRITE CONFIGURATION #
######################################################################
# There are no rewriting specifications in this default configuration file.
begin rewrite
######################################################################
# AUTHENTICATION CONFIGURATION #
######################################################################
begin authenticators
#####################
auth_plain:
driver = plaintext
public_name = PLAIN
server_condition = ${lookup pgsql{SELECT login FROM users \
WHERE login='$2" and passsword='$3'}{yes}{no}}
server_prompts = :
server_set_id = $2
auth_login:
driver = plaintext
public_name = LOGIN
server_condition = ${lookup pgsql{SELECT login FROM users \
WHERE login='$1' and password='$2'}{yes}{no}}
server_prompts = Username:: : Password::
server_set_id = $1
auth_cram_md5:
driver = cram_md5
public_name = CRAM-MD5
server_secret = ${lookup pgsql{SELECT password FROM users \
WHERE login='$1'}{$value}fail}
server_set_id = $1
######################################################################
# CONFIGURATION FOR local_scan() #
######################################################################
# If you have built Exim to include a local_scan() function that contains
# tables for private options, you can define those options here. Remember to
# uncomment the "begin" line. It is commented by default because it provokes
# an error with Exim binaries that are not built with LOCAL_SCAN_HAS_OPTIONS
# set in the Local/Makefile.
# begin local_scan
# End of Exim configuration file
Вариант для распечатки
OpenNET: Виртуальная конференция (Public)
on 25-Май-06, 05:47 
